Garage Cabinets
A Murrieta garage wall from bare drywall to finished cabinets, with the measuring steps, the clearances and four priced wall lengths.
Typically from $60/ft
Garage cabinets · Murrieta, CA
Garage Cabinets Summit Murrieta Garage Cabinets, Overhead Storage and Workbenches in Murrieta, CA
Garage Cabinets Summit Murrieta is a local guide and availability check for garage storage in Murrieta, CA — steel and custom cabinets, workbenches, overhead racks, slatwall and wall storage, and cabinets for shops, bays and maintenance rooms. Enter the length of wall for a typical price, sketch your garage in the layout planner, check whether an overhead rack fits under your ceiling, and see whether a local installer has bookings open for your ZIP yet.
Notify me when bookings open · typical prices in about 30 seconds
(951) 397-0110
Voicemail
Bookings aren't open yet. Leave your name and number; your message is recorded, and you'll get one message when a local installer is available.
- Murrieta prices per linear foot, by type of job
- Plain answers on heat, clearances and wall anchoring
- From Copper Canyon tracts to a bare builder-grade garage
Illustration
AI-generated illustration. The people shown are not real installers.
Price your garage by the foot
Take the questions one screen at a time: cabinets, overhead racks and wall storage, or a shop or business space. Then the length of wall, the system and the extras. The total moves with every answer and uses the same Murrieta area figures that appear on every page of this site.
Takes about 30 seconds · no sign-up to see your range
Check availability and get your Murrieta area price range
Bookings aren't open yet — a typical Murrieta range in about 30 seconds.
Sketch your garage before you ask for a price
Pick a garage size or type your own, mark the spots that have to stay clear, and drag cabinet runs onto the plan. The checks beside the plan show what is left for the cars and for the working spaces, and the length of the runs goes straight to the calculator. It is a planning aid, not a drawing for construction.
Drag a run along a wall, or pick it and use the buttons. Grid squares are 1 ft.
0 linear feet of wall covered
The total length of the base, wall, tall and bench runs is passed to the calculator as linear feet.
Width left for the cars
The plan subtracts the depth of the cabinet runs from the garage and shows how much width is left beside each parked car; cars and open doors need room, and the preset sizes are only a start.
Panel working space
Cabinet runs are kept out of a zone about 30 in. wide and 36 in. deep in front of the electrical panel (California Electrical Code, art. 110.26). Ask the building department about your panel.
Water heater access
Cabinets are planned around the water heater so it stays accessible, with its straps and combustion air untouched.
EV charger
A charger's connector height and cable reach need space; one city guide gives about 18 in. minimum for the connector. Check with the building department and the charger's maker.
Door to the house
The self-closing door between the garage and the house must keep swinging clear of every cabinet, and no opening is cut into the fire-rated wall.
A scale sketch drawn on screen; the garage is measured on site, and the installer and the maker decide the final layout.
Garage storage for local homes
One page for each decision: which system, where it hangs, and what has to stay clear.
Steel Garage Cabinets
Powder-coated steel for Murrieta garages, with a heat comparison of four box materials, a kit-versus-installed table and prices for three wall lengths.
Typically from $110/ft
Custom Garage Cabinets
Boxes built to fit an uneven wall, with a three-material comparison, a table for reading warranty fine print and two priced wall lengths.
Typically from $150/ft
Garage Makeover
A full garage plan for Murrieta homes, with the order of work, move-out and move-in, and three packages priced line by line.
Typically from $110/ft
Overhead Garage Storage
Ceiling racks for Murrieta garages, with where they fit around the door, what the framing must carry and a priced rack list.
Typically from $250/rack
Garage Workbench
Heights, tops and drawers for a Murrieta garage workbench, with a priced bench by length and a combined cabinet wall.
Typically from $60/ft
Garage Slatwall
Wall storage that hangs instead of sits, with a three-system comparison, a hook guide and prices for 8, 16 and 24 ft of wall.
Typically from $15/ft
Shop and business storage
Commercial Garage Cabinets
The business hub for Murrieta shops: the four kinds of space, three cabinet systems, anchoring, scheduling and a priced 40 ft run.
Auto Shop Cabinets
Cabinets for Murrieta repair bays and service departments, with a bay layout, drawer versus door cabinets and a priced 24 ft bay wall.
Warehouse and Maintenance Storage
Shelving and cabinets for maintenance rooms and small stockrooms in Murrieta, with a labeling plan and a priced 40 ft example.
Fleet and Contractor Garages
Storage for Murrieta trades that work out of a house garage or yard, with a loadout plan and two priced examples.
Steel, melamine, thermofoil or plywood: which survives a hot garage?
Every cabinet brochure praises its own material, so this is the side-by-side as plain trade-offs. Cost bands are Murrieta labor and material from the calculator on this page; the rest is general product behavior, and the maker's data sheet decides.
| Box material | Typical cost | Inland heat | Moisture and edges | What to ask for |
|---|---|---|---|---|
| Powder-coated steel, modular | $110–$190 per ft | Metal does not warp; dark colors get hot to the touch | A powder-coat finish resists corrosion better than raw steel; scratches can expose the metal | Steel gauge, finish type, leveling legs, hinge and slide ratings |
| Melamine or thermofoil custom boxes | $150–$260 per ft | Particleboard cores and thermofoil adhesives can soften or lift in long heat; makers differ | Cut and unsealed edges swell when wet | Edge banding on every edge, core type, the maker's stated temperature range |
| Plywood custom boxes | $220–$360 per ft | Stable in heat when the finish is sealed | Sealed faces and edges resist moisture; bare plywood does not | Species and plies, sealer or laminate on faces, fastener type |
| Ready-to-assemble system | $60–$110 per ft | Depends on the material; many are particleboard or thin steel | Same edge and finish questions | The maker's manual: load ratings, anchoring, warranty exclusions |
Cost bands are market estimates, not quotes. No claim of strength, lifespan or capacity is made for any row; compare gauges, edge sealing, hardware ratings and the maker's written limits.
What typical projects look like and what they cost
-
Illustration
Worked case: one wall of powder-coated steel cabinets in a two-car tract garage — steps and cost
Typical total $3,310–$7,170
-
Illustration
Worked case: cabinets, bench, slatwall and racks planned as one three-car layout — steps and cost
Typical total $11,110–$22,700
-
Illustration
Worked case: two ceiling racks and 16 feet of slatwall for bikes and seasonal bins — steps and cost
Typical total $1,150–$2,960
-
Illustration
Worked case: outfitting a bare three-car tract garage on a budget — steps and cost
Typical total $3,130–$6,880
-
Illustration
Worked case: modular drawer cabinets and a bench for a two-bay repair shop — steps and cost
Typical total $9,880–$20,320
-
Illustration
Worked case: shelving with cabinets for a property-maintenance room — steps and cost
Typical total $8,300–$17,900
Hypothetical typical projects. Pictures are AI-generated concept illustrations, not photos of completed installations; no installation was performed or arranged through this site; prices are typical Murrieta area market ranges, not quotes.
Will an overhead rack fit?
Enter the ceiling height and what hangs from it, and see roughly how much room a rack has. It is a rough guide: the door, the opener, the springs and the ceiling framing are checked on site, and the rack maker's manual decides.
—
A sectional door travels back along tracks near the ceiling, and its tracks, springs and the opener need clear space; racks go beside and behind them, never in their path.
Rack makers list drops from about 12 to 40 in.; the longer drops are for taller ceilings.
Before a rack goes up: the ceiling
- Find the ceiling joists with a stud finder; racks are fastened into joists, not into drywall alone.
- One maker's manual asks for 2×6 joists or larger at 24 in. on center at most, with lag screws about 2 in. into the framing; your rack's manual decides.
- Trusses and rafters differ from joists; a ceiling that is not plain joists is checked by a pro before any rack goes up.
- Do not hang a rack over the garage door path, the opener, or the water heater's flue or vent.
- Each rack has a stated load rating from its maker; stay inside it, and spread the weight.
General information; no rack, ceiling or load is guaranteed by this page.
Four fastenings behind a tidy garage wall
-
Wall cabinet on a mounting rail
- Stud
- Drywall
- Mounting rail
- Cabinet rail
- Cabinet body
- Tall-cabinet screw
Where it applies Suits wall cabinets: the weight transfers to the studs through the rail, and the cabinet is leveled on it.
Typically $110–$190 per ft about $2,800–$5,400 for 20 ft, installed
-
Tall cabinet anchored to the wall
- Concrete floor
- Leveling legs
- Tall cabinet
- Wall stud and drywall
- Upper bracket
- Lower bracket
Where it applies Suits tall cabinets, which can tip when the doors are open and loaded; an anchor into a stud holds the top rail to the wall.
Typically $110–$190 per ft about $3,600–$7,000 for 20 ft, installed
-
Overhead rack beside the door track
- Door track
- Opener rail
- Open door
- Rack zone
- Keep-clear zone
Where it applies Suits ceiling racks: the brackets are fastened into framing, never into drywall alone, within the maker's stated load.
Typically $25–$60 per ft about $1,000–$2,360 for 16 ft, installed
-
Slatwall on studs
- Studs
- Drywall
- Slatwall panel
- Screws into studs
- Hook
Where it applies Suits wall storage next to the zones a ceiling rack must avoid: slatwall goes onto studs and keeps tools and bikes off the floor.
Typically $25–$60 per ft about $480–$1,200 for 16 ft, installed
Shop and business storage
-
Auto repair bay
Heavy-gauge drawer cabinets, a bench and tool storage along the bay wall, fitted around the lift and the air lines.
-
Maintenance room
Steel shelving with cabinets and labeled bins for parts, anchored to the wall.
-
Contractor garage
Van stock, tool walls and locking cabinets for a trade run from a garage or a yard.
-
Retail or office back room
Cabinets and benches that keep supplies tidy and out of the customer's sight.
A cabinet project in six steps
Measure and markWalls, ceiling height and door track are measured, and the water heater, the electrical panel, the outlets and the door to the house are marked so cabinets can be planned around them.
Lay out the runsBase, wall and tall cabinets, the workbench and any racks are placed on a plan, with the working spaces in front of the panel and the heater left clear.
Order and waitCabinets are made or shipped to the order; the lead time depends on the maker and the material, and the installer states it.
Prepare the garageThe contents come out, old shelving comes down, studs and ceiling framing are located, and a floor that was coated is protected.
Hang, level and anchorFloor cabinets are leveled, wall cabinets go onto a mounting rail or cleat into studs, tall cabinets are anchored, and racks are fastened into framing as the maker directs.
Load in and tidyDoors and drawers are adjusted, packaging and old shelving leave, and the contents go back onto labeled shelves.
Outfitting a builder-grade garage
Most Murrieta garages were built between the 1990s and the 2010s and left with bare drywall and a few wire shelves. The year the house was built is a good first clue to what the garage holds and what has to be planned around. The table is general; the actual garage is measured on site.
| Home built | Likely situation | Typical question | Plan first |
|---|---|---|---|
| Before 1990 | Older tract and ranch homes, Old Town streets and the Ranchos; smaller garages | Depth for cabinets and a parked car, an older panel location | Measure width and depth; keep the panel and the water heater clear |
| 1990 to 1999 | Early master-planned tracts; two- and three-car garages with a water heater in a corner | Builder shelving to remove, a bare back wall | A full back wall of cabinets and a workbench |
| 2000 to 2009 | The bulk of Murrieta's housing; 3-car garages, tall ceilings in places | Overhead racks, a hot west-facing wall | Check the ceiling framing and the door track before a rack |
| 2010 and later | Newer tracts, smaller lots, HOAs, an EV charger on the wall | A charger and a panel upgrade near the cabinet runs | Leave room around the charger and the panel; read the CC&Rs |
The median Murrieta home was built around 2001, and only about 4% of homes date from before 1980, so there are few cramped mid-century garages here. More than half of the housing (56%) was built in 2000 or later, which is why the usual starting point is an empty builder-grade garage.
About 68% of households own and 32% rent, and about 71% of homes are detached houses. Owners decide for themselves; for a rental the lease decides, and a landlord may prefer freestanding units to anything fixed to the wall. Cabinets are planned around the house the garage belongs to, and the CC&Rs or the lease decide what is allowed.
The climate sets the material question. July highs average about 91°F, January highs about 67°F, and about 15.6 inches of rain falls a year, almost all in winter. A closed garage can run well above the outdoor temperature on a summer afternoon, so box material, edge sealing and hardware ratings matter more here than a catalog color.
Bare garage checklist
- Wire shelves and a few brackets on the wall
- Remove them first; fill or patch the holes before cabinets go up, and locate studs with a finder
- Water heater in a corner
- Keep it accessible and leave its straps and combustion air alone; cabinets are planned around it
- Electrical panel on a side wall
- Keep about 30 in. of width and 36 in. of depth clear in front of it; no cabinet doors swinging into that space
- Garage door tracks, springs and the opener
- Overhead racks are planned beside the track and clear of the opener; the door must still clear everything
- A coated floor planned or already done
- The order is floor first and cabinets after the cure the floor maker states; protect the floor while the cabinets go in
Eight questions to ask before accepting a garage storage bid
- What does the price include: removal of old shelving, wall repair, hardware, a workbench top, lighting, and moving the contents out and back?
- Which box material and thickness, or which steel gauge, and which hinges and drawer slides, with their load ratings written down?
- How are wall and tall cabinets attached: into studs with what fasteners, and how are tall cabinets anchored against tipping?
- For an overhead rack: how are the ceiling joists checked, which fasteners go in, and what load rating does the maker state?
- How will the cabinets be planned around the water heater, the electrical panel and the door to the house?
- What is the lead time, how many days is the installation, and what happens if the order is late?
- What does the warranty cover (finish, hinges, slides, workmanship), for how long, and what does it exclude, in writing?
- What is the payment schedule, and has the contractor's license been checked at cslb.ca.gov?
Check the contractor's license at cslb.ca.gov before signing; work above $1,000 requires one.
- 91°Faverage July afternoon high in Murrieta (1991–2020 normals)
- 56%of local housing was built in 2000 or later, so most garages are builder-grade
- $1,000California's limit on work an unlicensed person may do
- 30 × 36 in.about the working space kept clear in front of an electrical panel (California Electrical Code)
Garage cabinet questions
How much do garage cabinets cost in Murrieta, CA?
For 2026 a typical Murrieta range is about $60–$110 per linear foot installed for a ready-to-assemble system, $110–$190 for powder-coated steel, $150–$260 for melamine or thermofoil boxes and $220–$360 for plywood boxes, before wall cabinets and options. Wall cabinets add about $30–$80 per foot and tall cabinets about $70–$160. One 20-foot wall of steel base and wall cabinets comes to roughly $2,800–$5,400. These are market estimates, not quotes.
What do overhead racks and slatwall cost?
Typically $300–$700 per overhead rack with installation, $25–$60 per foot for PVC slatwall and $40–$90 per foot for a steel rail system, with a joist check of $150–$600 where the ceiling needs added blocking. Market estimates, not quotes.
Which cabinet material handles a hot garage?
Powder-coated steel and sealed plywood are generally the steadier choices; particleboard cores and thermofoil adhesives can soften or lift in long heat, and unsealed edges swell if they get wet. Makers differ, so ask for the stated temperature range and the edge treatment in writing.
Do cabinets have to stay away from the water heater and the electrical panel?
They are planned around them. The space in front of an electrical panel is kept clear (about 30 in. wide and 36 in. deep under the California Electrical Code), the water heater stays accessible with its straps and air supply untouched, and the door to the house keeps its swing. The building department has the final word.
Can a ceiling rack go over my parked car?
Often, but only if the ceiling is high enough and the framing is right. Racks are fastened into joists, they have to stay out of the way of the door tracks, springs and opener, and each has a load rating from its maker. The rack-fit calculator on this page gives a first idea; the garage is checked on site.
Do tall cabinets need to be anchored to the wall?
Yes, as the maker's instructions require. Tall cabinets can tip when loaded and open, so they are anchored to studs, and wall cabinets hang on a rail or cleat fixed into studs. No cabinet is called earthquake-proof.
Is it cheaper to buy a kit from a big retailer and install it myself?
A kit often costs less up front, and the work is yours: studs, level walls, anchoring and the maker's load ratings. The comparison guide on this site sets kits next to installed systems; read what each warranty excludes.
Should the garage floor be coated first or the cabinets installed first?
The usual order is the floor first and the cabinets after the cure time the floor maker states, with the floor protected while the cabinets go in. This site covers cabinets and storage only.
Do I need an HOA's permission for garage cabinets?
Work inside a garage is usually not an association matter, but contractor hours, parking and an open garage door can be. The CC&Rs decide, and for a rental the lease decides.
How long does an installation take?
Many wall systems go in over a day or two once the cabinets are on site; the order itself can take weeks, depending on the maker and the material. The installer states both times.
Do you cover shops, bays and maintenance rooms too?
Yes. The Shops & business pages cover auto repair bays, maintenance rooms, contractor and fleet garages and heavy-gauge commercial cabinets, with their own path in the calculator. Schools, fire stations and other public agencies are outside this site.
Which parts of Murrieta are covered?
Homes and businesses across Murrieta, CA — Copper Canyon, Clarendon Hills and Vintage Reserve, Central Park, Bear Creek, Greer Ranch, Alta Murrieta, Old Town Murrieta, and Murrieta Ranchos and La Cresta. The availability check shows whether bookings are open for a ZIP.
Who does the work?
Contractors featured on this site are independent businesses. The contractor's legal name and business details are published on this site before bookings open. Warranty terms, if any, are set by the contractor and the manufacturer; ask what is covered, for how long, and what is excluded.
Neighborhoods covered
Garage Cabinets Summit Murrieta covers Copper Canyon, Clarendon Hills and Vintage Reserve, Central Park, Bear Creek, Greer Ranch, Alta Murrieta, Old Town Murrieta, Murrieta Ranchos and La Cresta — pick your neighborhood from the menu for local details and ZIP codes.
Copper CanyonLate-1990s tract homes and townhomes between Clinton Keith Road and Washington Avenue
Clarendon Hills and Vintage ReserveOne-story homes with three-car garages along Date Street near the Temecula line
Central ParkAbout 500 homes east of Winchester Road in The Commons and Hillcrest Estates
Bear CreekA guard-gated golf community with three-car garages
Greer RanchA master-planned gated community off the I-15 at Clinton Keith Road
Alta MurrietaLate-1980s and early-1990s cul-de-sac streets near Murrieta Hot Springs Road
Old Town MurrietaSmall lots and older homes around the 1887 depot and Washington Avenue
Murrieta Ranchos and La CrestaLarger lots in west Murrieta below the Santa Rosa Plateau, with detached and oversized garages